Taco
Showing 1–15 of 25 results
-
Hydronic, Inline Pumps, Pumps
Taco 1900 Series
Close Coupled In-Line Pumps
GPM: 7 – 280
Head (ft): 6 – 164
HP: 1/4 – 7-1/2
Sizes (in): 1-1/2
Self-supporting design which allows horizonal or vertical installation
Pump and sealed ball bearing motor are maintenance-free
Rear pullout design and standard motor promote simple, easy service
One seal and shaft sleeve fits all models, assuring superior party flexibilitySKU: n/a -
Air/Dirt Separators, Hydronic, Hydronic Accessories
Taco 4900 Series (Air or Air/Dirt Separator)
GPM: 0 – 33,457
Connection Sizes (in): 2 – 36
Option to remove dirt as well as air
Optional removable heads and Pall ring baskets
Micro air bubble removal to 18 microns
Dirt particle removal below 30 microns
Designed and constructed per ASME Section VIII Div 1.SKU: n/a -
Air/Dirt Separators, Hydronic, Hydronic Accessories
Taco 5900 Series (Air or Air/Dirt Separator and Decoupler)
Air/Dirt Separators, Hydronic, Hydronic AccessoriesTaco 5900 Series (Air or Air/Dirt Separator and Decoupler)
GPM: 0 – 1,409
Connection Sizes (in): 2 – 12
Acts as a hydraulic bridge (decoupler) between two loops
Optional pall ring technology for deep micro-bubble and dirt removal
Designed and constructed per ASME Section VIII Div 1.SKU: n/a -
Buffer Tanks, Hydronic, Hydronic Accessories
Taco BH Series (Horizontal)
Buffer tanks providing additional system fluid volume to prevent short cycling
Capacity (gal): 50 – 3,000
Flange Sizes (in.): 2 – 12
Diameter (in.): 20 – 84
Height (in.): 50 – 160
Construction in carbon steel with exterior red oxide primer finish
Flanged inlet and outlet system connections
Designed and constructed per ASME Section VIII Div 1.SKU: n/a -
-
Buffer Tanks, Hydronic, Hydronic Accessories
Taco BT Series (Vertical)
Buffer tanks providing additional system fluid volume to prevent short cycling
Capacity (gal): 50 – 3,000
Flange Sizes (in.): 2 – 12
Diameter (in.): 20 – 84
Height (in.): 50 – 160
Construction in carbon steel with exterior red oxide primer finish
Flanged inlet and outlet system connections
Designed and constructed per ASME Section VIII Div 1.SKU: n/a -
Expansion Tanks, Hydronic, Hydronic Accessories
Taco CA Series
Bladder type expansion tank
Capacity: 23 – 2,640 Gal. (90 – 10,000 liters)
Diameter (in.): 20 – 72
Height (in.): 29 – 160
Réservoirs d’expansions pour application nécessitant une certification NSF/ANSI 61-G
Type de réservoir d’expansion d’air captif qui aide à réduire la taille des réservoirs d’expansions
La vessie est amovible sur le terrain
Steel shell is designed and constructed per ASME Section VIII Div 1.SKU: n/a -
Expansion Tanks, Hydronic, Hydronic Accessories
Taco CBX Series
Bladder type expansion tanks
Capacity: 4 – 212 Gal. (15 – 800 liters)
Diameter (in.): 14 – 30
Height (in.): 15 – 86
Water expands into bladder, air precharge on shell side
Steel shell is designed and constructed per ASME Section VIII Div 1.SKU: n/a -
Expansion Tanks, Hydronic, Hydronic Accessories
Taco CW Series
Bladder type for permanent separation of air and water
Water expands into bladder, air pre charge on shell side
Designed and constructed per ASME Section VIII Div 1. and pressure vessel code
All wetted surfaces of FDA approved materials for potable water applications
Internal bladder is field replaceable and removeable
Working pressure standard: 125 PSIG, optional: 150 & 250 PSIG
304 stainless steel system connection
Capacity from 158-528 GALSKU: n/a -
Expansion Tanks, Hydronic, Hydronic Accessories
Taco CX Series
Diaphragm type expansion tank
Capacity: 8 – 92 Gal. (30 – 350 liters)
Diameter (in.): 14 – 24
Height (in.): 22 – 60
Diaphragm with heavy duty butyl (non replaceable)
Steel shell is designed and constructed per ASME Section VIII Div 1.SKU: n/a -
Base-Mounted Pumps, Hydronic, Pumps
Taco FI/CI Series
FI – Base Mounted End Suction Pump
GPM: 40 – 4,400
Head (ft): 1 – 390
HP: 1/2- 150
Sizes (in): 1-1/2 – 8CI – Close-Coupled End Suction Pump
Max. Flow (GPM): 2500
Max. Head (ft): 181
HP: 1/2 – 50
Sizes (in.): 2 x 1-1/4 – 8 x 6Cast iron casing and allows for back pull without disturbing piping
1/4 NPT pressure tapping on suction and discharge connections
Low-cost, replaceable wear rings protecting casing during normal operation
Standard ceramic seals and dry shaft designSKU: n/a -
Base-Mounted Pumps, Hydronic, Pumps
Taco GT/TA Series
GT – Horizontal Split Case Pump
GPM: 1,167 – 19,150
Head (ft): 18 – 427
HP: 30 – 1,500
Sizes (in): 10 – 18TA – Horizontal Split Case Pump
GPM: 101 – 5,805
Head (ft): 11 – 385
HP: 1 – 450
Sizes (in): 2 – 10Cast iron pump casing with high-efficiency double suction bronze or stainless steel impeller
Carbon steel or stainless steel shaft
Bronze or stainless steel shaft sleeve
Rugged, heave-duty casing design for higher working pressures
Low-cost, replaceable wear rings to protect casing during normal operationSKU: n/a -
Hydronic, Inline Pumps, Pumps
Taco KS/KV Series
KV – Vertical In-Line Pumps
GPM: 10 – 2,650
Head (ft): 11 – 385
HP: 3/4 – 60
Sizes (in): 1-1/2 – 8KS – Vertical Split-Coupled In-Line Pump
GPM: 40 – 12,000
Head (ft): 10 – 380
HP: 3/4 – 600
Sizes: 1-1/2-14Split-coupled (KS) permits changing of the seal without disturbing motor or piping
Axial load hydraulically balanced to increase bearing life and lower NPSH requirements
Standard pump construction in cast-iron, bronze impeller and stainless steel shaft
Option for NSF 61 with cast iron casing and stainless steel impeller and shaft
Mechanical seal in cermaic/EPT, option for Tungsten carbide providedSKU: n/a -
Circulators, Hydronic, Pumps
Taco LoadMatch
Advanced hydronic system for heating and cooling for lower energy and maintenance costs
LoadMatch system includes: circulators, thermostats and twin-tee fittings to obtain higher efficiency
Design can be simulated with Taco Hydronic System Solution (HSS)
Twin-tee is a single pipe fitting that can be used in both single and two pipe systemsSKU: n/a -