Water Heaters
Showing 1–15 of 29 results
-
Heating, Water Heater Heat Exchanger, Water Heaters
P-K Duration
300 MBTU to 2 000 MBTU
Specifically designed to prevent scale build-up
Available with single or double wall heat exchanger
Custom designed skid available, delivered ready to install at the job site
Available for domestic water heat recoverySKU: n/a -
Condensing Water Heaters, Heating, Water Heaters
P-K MACH’n Roll Boiler
300 MBTU to 1050 MBTU
Domestic water loop is isolated from the boiler loop
Precise temperature regulation with no mixing valve required
Onboard P-K ENVI® control system
Certified low NOx performance
Aluminum alloy heat exchanger
Full modulation burner with 5:1 turndown
Produce domestic water up to 140°F and still operate the boiler in the condensing modeSKU: n/a -
Heating, Non-Condensing Water Heaters, Water Heaters
P-K Thermific Water Heater
700 MBTU to 2000 MBTU
Efficiency up to 85%
Completely packaged design, including burner and controls, pre-wired and mounted
Compact/modular design allows multiple units to be installed in tandem
Copper heat exchanger, water tubes
High heat transfer ratio Lo-Hi-Lo operating controls on some models
Operates quietly
CSA (AGA/CGA) certified and ASME approvedSKU: n/a -
Heating, Non-Condensing Water Heaters, Water Heaters
Raypak EconoPak Series Water Heaters
90 MBTH to 399 MBTH
Indoor and outdoor models
82% thermal efficiency
Factory mounted and wired stainless steel pump
Consistent 140°F water delivery, even during peak demand times
Compact
20 year limited warranty
SKU: n/a -
Heating, Non-Condensing Water Heaters, Water Heaters
Raypak Hi Delta Series Water Heaters
100 MBTH to 2,340 MBTH
Indoor and outdoor models
84% efficiency
Cat I (vertical venting)/Cat III (sidewall venting)
Cast iron (Brass opt.) headers with copper (cupronickel opt.) finned tube heat exchanger
Ducted combustion air ready
105°F minimum inlet water temperature
On/Off to 4 stage operation
Cascade control of up to 4 units
VERSA IC® Control Package with LCD Display
Diagnostics Center with History, English, no codes
0-10 VDC BMS Interface
Optionnal Dual Fuel
SKU: n/a -
Heating, Non-Condensing Water Heaters, Water Heaters
Raypak Modulating Vertical Series Water Heaters
500 MBTH to 4,000 MBTH
Indoor and outdoor models
84% thermal efficiency at full rate
Cat I/IV venting required (depending on the model)
Cast iron/Bronze (Brass opt.) headers with copper (cupronickel opt.) finned tube heat exchanger
120°F minimum inlet water temperature
150°F maximum setpoint temperature
Electronic modulation up to 7:1 turndown
Cascade control of up to 4 units
VERSA IC® Control Package with Built-In Outdoor Reset Function, LCD Display
Diagnostics Center with History, English, no codes
0-10 VDC BMS Interface
Small footprint
SKU: n/a -
Heating, Non-Condensing Water Heaters, Water Heaters
Raypak Raytherm Series Water Heaters
181 MBTH to 4,000 MBTH
Indoor or outdoor models
82% thermal efficiency
Cat I venting
Cast iron/Rugged All-Brass (Brass opt.) headers with copper (cupronickel opt.) finned tube heat exchanger
24-Volt Controls
Floating return header
Corrosion resistant steel
Stainless steel burners
Optionnal Low Nox Water Heater
Mechanical modulation, On/Off, 2-Stage, 4-Stage operation (depending on the model)
A condensing version is available
SKU: n/a -
Heating, Non-Condensing Water Heaters, Water Heaters
Raypak X-Therm Series Ultra-High Efficiency Water Heaters
999 MBTH to 4,000 MBTH
Indoor and outdoor models
97% efficiency at full fire
Condensing, Cat IV venting required
Brass headers and pumps with copper (cupronickel opt.) finned tube heat exchanger
50°F minimum continuous inlet temperature
Modulation up to 12.5:1 turndown
On-board diagnostic center, real English, no codes
Primary-secondary piping required
VERSA IC® control package
Built-in cascade function for up to 4 boilers
Low NOxSKU: n/a -
Heating, Non-Condensing Water Heaters, Water Heaters
Raypak Xfyre Series Water Heaters
300 MBTH to 850 MBTH
Indoor and outdoor models
95% efficiency condensing (up to 99% at part load)
Cat IV venting required
Small footprint
Top side water connections – allows side by side installation
316L welded stainless steel heat exchanger and copper plumbing
Modulation up to 5:1 turndown
50°F Minimum inlet water temperature
On-board diagnostic center, English, no codes
Built-in cascade function for up to 4 boilers
VERSA IC® control packageSKU: n/a -
Heating, Non-Condensing Water Heaters, Water Heaters
RBI 8800 Series domestic water heater (HW)
2 800 MBH to 4 000 MBH
Cast iron (Bronze optional) headers
Copper (Cupro-Nickel optional) finned tube heat exchanger, certified ASME
Slide out heat exchanger and burner tray for easy maintenance
Heavy Duty Structural Steel Frame
Available modulation: On/Off, 2-Stage, 4-Stage
Venting: Category I and IIISKU: n/a -
Heating, Non-Condensing Water Heaters, Water Heaters
RBI 8900 Series domestic water heater (HW)
530 MBH to 1 900 MBH
Cast iron headers (Bronze optional)
Copper (Cupro-Nickel optional) finned tube heat exchanger, certified ASME
Heavy Duty Structural Steel Frame
Slide out heat exchanger for easy maintenance
Available modulation: On/Off, 2-Stage, 4-Stage
Venting: Category I and IIISKU: n/a -
Heating, Non-Condensing Water Heaters, Water Heaters
RBI Dominator Series water heater (DW)
300 MBH to 2 100 MBH
Up to 85 % efficiency
Bronze headers
Copper (Cupro-Nickel optional) finned tube heat exchanger, water tube
Slide-Out Heat Exchanger for easy maintenance
Available modulation: On/Off (300 MBH only), 2-Stage, 4-Stage
Barometric Damper (Cat I)
Optional outdoor installation available
Venting : Category I and IIISKU: n/a -
Condensing Water Heaters, Heating, Water Heaters
RBI Futera Fusion Series water heater (CW)
500 MBH to 2 000 MBH
Up to 95 % efficiency
Copper (Cupro-Nickel optional) finned tube heat exchanger, water tube
Full modulation burner Low NOx with 4:1 turndown
HeatNet 3.0 integrated control system (with optional touchscreen)
Venting: Category II and IVSKU: n/a
-
Heating, Water Heater Heat Exchanger, Water Heaters
P-K Duration
300 MBTU to 2 000 MBTU
Specifically designed to prevent scale build-up
Available with single or double wall heat exchanger
Custom designed skid available, delivered ready to install at the job site
Available for domestic water heat recovery -
Condensing Water Heaters, Heating, Water Heaters
P-K MACH’n Roll Boiler
300 MBTU to 1050 MBTU
Domestic water loop is isolated from the boiler loop
Precise temperature regulation with no mixing valve required
Onboard P-K ENVI® control system
Certified low NOx performance
Aluminum alloy heat exchanger
Full modulation burner with 5:1 turndown
Produce domestic water up to 140°F and still operate the boiler in the condensing mode -
Heating, Non-Condensing Water Heaters, Water Heaters
P-K Thermific Water Heater
700 MBTU to 2000 MBTU
Efficiency up to 85%
Completely packaged design, including burner and controls, pre-wired and mounted
Compact/modular design allows multiple units to be installed in tandem
Copper heat exchanger, water tubes
High heat transfer ratio Lo-Hi-Lo operating controls on some models
Operates quietly
CSA (AGA/CGA) certified and ASME approved -
Heating, Non-Condensing Water Heaters, Water Heaters
Raypak EconoPak Series Water Heaters
90 MBTH to 399 MBTH
Indoor and outdoor models
82% thermal efficiency
Factory mounted and wired stainless steel pump
Consistent 140°F water delivery, even during peak demand times
Compact
20 year limited warranty
-
Heating, Non-Condensing Water Heaters, Water Heaters
Raypak Hi Delta Series Water Heaters
100 MBTH to 2,340 MBTH
Indoor and outdoor models
84% efficiency
Cat I (vertical venting)/Cat III (sidewall venting)
Cast iron (Brass opt.) headers with copper (cupronickel opt.) finned tube heat exchanger
Ducted combustion air ready
105°F minimum inlet water temperature
On/Off to 4 stage operation
Cascade control of up to 4 units
VERSA IC® Control Package with LCD Display
Diagnostics Center with History, English, no codes
0-10 VDC BMS Interface
Optionnal Dual Fuel
-
Heating, Non-Condensing Water Heaters, Water Heaters
Raypak Modulating Vertical Series Water Heaters
500 MBTH to 4,000 MBTH
Indoor and outdoor models
84% thermal efficiency at full rate
Cat I/IV venting required (depending on the model)
Cast iron/Bronze (Brass opt.) headers with copper (cupronickel opt.) finned tube heat exchanger
120°F minimum inlet water temperature
150°F maximum setpoint temperature
Electronic modulation up to 7:1 turndown
Cascade control of up to 4 units
VERSA IC® Control Package with Built-In Outdoor Reset Function, LCD Display
Diagnostics Center with History, English, no codes
0-10 VDC BMS Interface
Small footprint
-
Heating, Non-Condensing Water Heaters, Water Heaters
Raypak Raytherm Series Water Heaters
181 MBTH to 4,000 MBTH
Indoor or outdoor models
82% thermal efficiency
Cat I venting
Cast iron/Rugged All-Brass (Brass opt.) headers with copper (cupronickel opt.) finned tube heat exchanger
24-Volt Controls
Floating return header
Corrosion resistant steel
Stainless steel burners
Optionnal Low Nox Water Heater
Mechanical modulation, On/Off, 2-Stage, 4-Stage operation (depending on the model)
A condensing version is available
-
Heating, Non-Condensing Water Heaters, Water Heaters
Raypak X-Therm Series Ultra-High Efficiency Water Heaters
999 MBTH to 4,000 MBTH
Indoor and outdoor models
97% efficiency at full fire
Condensing, Cat IV venting required
Brass headers and pumps with copper (cupronickel opt.) finned tube heat exchanger
50°F minimum continuous inlet temperature
Modulation up to 12.5:1 turndown
On-board diagnostic center, real English, no codes
Primary-secondary piping required
VERSA IC® control package
Built-in cascade function for up to 4 boilers
Low NOx -
Heating, Non-Condensing Water Heaters, Water Heaters
Raypak Xfyre Series Water Heaters
300 MBTH to 850 MBTH
Indoor and outdoor models
95% efficiency condensing (up to 99% at part load)
Cat IV venting required
Small footprint
Top side water connections – allows side by side installation
316L welded stainless steel heat exchanger and copper plumbing
Modulation up to 5:1 turndown
50°F Minimum inlet water temperature
On-board diagnostic center, English, no codes
Built-in cascade function for up to 4 boilers
VERSA IC® control package -
Heating, Non-Condensing Water Heaters, Water Heaters
RBI 8800 Series domestic water heater (HW)
2 800 MBH to 4 000 MBH
Cast iron (Bronze optional) headers
Copper (Cupro-Nickel optional) finned tube heat exchanger, certified ASME
Slide out heat exchanger and burner tray for easy maintenance
Heavy Duty Structural Steel Frame
Available modulation: On/Off, 2-Stage, 4-Stage
Venting: Category I and III -
Heating, Non-Condensing Water Heaters, Water Heaters
RBI 8900 Series domestic water heater (HW)
530 MBH to 1 900 MBH
Cast iron headers (Bronze optional)
Copper (Cupro-Nickel optional) finned tube heat exchanger, certified ASME
Heavy Duty Structural Steel Frame
Slide out heat exchanger for easy maintenance
Available modulation: On/Off, 2-Stage, 4-Stage
Venting: Category I and III -
Heating, Non-Condensing Water Heaters, Water Heaters
RBI Dominator Series water heater (DW)
300 MBH to 2 100 MBH
Up to 85 % efficiency
Bronze headers
Copper (Cupro-Nickel optional) finned tube heat exchanger, water tube
Slide-Out Heat Exchanger for easy maintenance
Available modulation: On/Off (300 MBH only), 2-Stage, 4-Stage
Barometric Damper (Cat I)
Optional outdoor installation available
Venting : Category I and III -
Condensing Water Heaters, Heating, Water Heaters
RBI Futera Fusion Series water heater (CW)
500 MBH to 2 000 MBH
Up to 95 % efficiency
Copper (Cupro-Nickel optional) finned tube heat exchanger, water tube
Full modulation burner Low NOx with 4:1 turndown
HeatNet 3.0 integrated control system (with optional touchscreen)
Venting: Category II and IV
-
Heating, Water Heater Heat Exchanger, Water Heaters
P-K Duration
300 MBTU to 2 000 MBTU
Specifically designed to prevent scale build-up
Available with single or double wall heat exchanger
Custom designed skid available, delivered ready to install at the job site
Available for domestic water heat recovery -
Condensing Water Heaters, Heating, Water Heaters
P-K MACH’n Roll Boiler
300 MBTU to 1050 MBTU
Domestic water loop is isolated from the boiler loop
Precise temperature regulation with no mixing valve required
Onboard P-K ENVI® control system
Certified low NOx performance
Aluminum alloy heat exchanger
Full modulation burner with 5:1 turndown
Produce domestic water up to 140°F and still operate the boiler in the condensing mode -
Heating, Non-Condensing Water Heaters, Water Heaters
P-K Thermific Water Heater
700 MBTU to 2000 MBTU
Efficiency up to 85%
Completely packaged design, including burner and controls, pre-wired and mounted
Compact/modular design allows multiple units to be installed in tandem
Copper heat exchanger, water tubes
High heat transfer ratio Lo-Hi-Lo operating controls on some models
Operates quietly
CSA (AGA/CGA) certified and ASME approved -
Heating, Non-Condensing Water Heaters, Water Heaters
Raypak EconoPak Series Water Heaters
90 MBTH to 399 MBTH
Indoor and outdoor models
82% thermal efficiency
Factory mounted and wired stainless steel pump
Consistent 140°F water delivery, even during peak demand times
Compact
20 year limited warranty
-
Heating, Non-Condensing Water Heaters, Water Heaters
Raypak Hi Delta Series Water Heaters
100 MBTH to 2,340 MBTH
Indoor and outdoor models
84% efficiency
Cat I (vertical venting)/Cat III (sidewall venting)
Cast iron (Brass opt.) headers with copper (cupronickel opt.) finned tube heat exchanger
Ducted combustion air ready
105°F minimum inlet water temperature
On/Off to 4 stage operation
Cascade control of up to 4 units
VERSA IC® Control Package with LCD Display
Diagnostics Center with History, English, no codes
0-10 VDC BMS Interface
Optionnal Dual Fuel
-
Heating, Non-Condensing Water Heaters, Water Heaters
Raypak Modulating Vertical Series Water Heaters
500 MBTH to 4,000 MBTH
Indoor and outdoor models
84% thermal efficiency at full rate
Cat I/IV venting required (depending on the model)
Cast iron/Bronze (Brass opt.) headers with copper (cupronickel opt.) finned tube heat exchanger
120°F minimum inlet water temperature
150°F maximum setpoint temperature
Electronic modulation up to 7:1 turndown
Cascade control of up to 4 units
VERSA IC® Control Package with Built-In Outdoor Reset Function, LCD Display
Diagnostics Center with History, English, no codes
0-10 VDC BMS Interface
Small footprint
-
Heating, Non-Condensing Water Heaters, Water Heaters
Raypak Raytherm Series Water Heaters
181 MBTH to 4,000 MBTH
Indoor or outdoor models
82% thermal efficiency
Cat I venting
Cast iron/Rugged All-Brass (Brass opt.) headers with copper (cupronickel opt.) finned tube heat exchanger
24-Volt Controls
Floating return header
Corrosion resistant steel
Stainless steel burners
Optionnal Low Nox Water Heater
Mechanical modulation, On/Off, 2-Stage, 4-Stage operation (depending on the model)
A condensing version is available
-
Heating, Non-Condensing Water Heaters, Water Heaters
Raypak X-Therm Series Ultra-High Efficiency Water Heaters
999 MBTH to 4,000 MBTH
Indoor and outdoor models
97% efficiency at full fire
Condensing, Cat IV venting required
Brass headers and pumps with copper (cupronickel opt.) finned tube heat exchanger
50°F minimum continuous inlet temperature
Modulation up to 12.5:1 turndown
On-board diagnostic center, real English, no codes
Primary-secondary piping required
VERSA IC® control package
Built-in cascade function for up to 4 boilers
Low NOx -
Heating, Non-Condensing Water Heaters, Water Heaters
Raypak Xfyre Series Water Heaters
300 MBTH to 850 MBTH
Indoor and outdoor models
95% efficiency condensing (up to 99% at part load)
Cat IV venting required
Small footprint
Top side water connections – allows side by side installation
316L welded stainless steel heat exchanger and copper plumbing
Modulation up to 5:1 turndown
50°F Minimum inlet water temperature
On-board diagnostic center, English, no codes
Built-in cascade function for up to 4 boilers
VERSA IC® control package -
Heating, Non-Condensing Water Heaters, Water Heaters
RBI 8800 Series domestic water heater (HW)
2 800 MBH to 4 000 MBH
Cast iron (Bronze optional) headers
Copper (Cupro-Nickel optional) finned tube heat exchanger, certified ASME
Slide out heat exchanger and burner tray for easy maintenance
Heavy Duty Structural Steel Frame
Available modulation: On/Off, 2-Stage, 4-Stage
Venting: Category I and III -
Heating, Non-Condensing Water Heaters, Water Heaters
RBI 8900 Series domestic water heater (HW)
530 MBH to 1 900 MBH
Cast iron headers (Bronze optional)
Copper (Cupro-Nickel optional) finned tube heat exchanger, certified ASME
Heavy Duty Structural Steel Frame
Slide out heat exchanger for easy maintenance
Available modulation: On/Off, 2-Stage, 4-Stage
Venting: Category I and III -
Heating, Non-Condensing Water Heaters, Water Heaters
RBI Dominator Series water heater (DW)
300 MBH to 2 100 MBH
Up to 85 % efficiency
Bronze headers
Copper (Cupro-Nickel optional) finned tube heat exchanger, water tube
Slide-Out Heat Exchanger for easy maintenance
Available modulation: On/Off (300 MBH only), 2-Stage, 4-Stage
Barometric Damper (Cat I)
Optional outdoor installation available
Venting : Category I and III -
Condensing Water Heaters, Heating, Water Heaters
RBI Futera Fusion Series water heater (CW)
500 MBH to 2 000 MBH
Up to 95 % efficiency
Copper (Cupro-Nickel optional) finned tube heat exchanger, water tube
Full modulation burner Low NOx with 4:1 turndown
HeatNet 3.0 integrated control system (with optional touchscreen)
Venting: Category II and IV