Chimney System
Showing all 10 results
-
Chimney System, Heating
Centrotherm BlitzFlex®
- Flexible air-intake system.
- Made from flexible polymer BlitzFlex® comes in an easy to dispense BlitzPack box.
- A single box provides enough flexible air-intake conduit to complete 3 to 5 standard residential systems.
- Available in 2’’, 3’’ and 4’’ diameter they can be combined with BlitzKits which includes a rigid vent length, a 45° elbow, an appliance adaptor, and support clamps.
- Residential and light commercial air-intake installations have never been faster and easier.
SKU: n/a -
Chimney System, Heating
Centrotherm InnoFlue®
- Single wall polypropylene venting systems
- InnoFlue® polypropylene venting system come in a variety of sizes up to 10’ in length.
- Residential: 2’’, 3’’, 4’’ and 5’’ diameter – Commercial: 6’’, 8’’, 10’’ and 12’’ diameter.
- Industry leading flame retardant polypropylene technology rated to 230°F, tested to UL-1738 and ULC-S636.
- Zero clearance to combustibles and is suitable for Category II and IV or Type BH Gas Vent.
- No glue or solvent required.
- Vent Lengths and fittings are joined using high performance EPDM gaskets which are suitable for service pressures up to 20’’WC.
- Lightweight polypropylene eliminates installation fatigue associated with overhead installation of most common venting materials.
- Can be configured to vent individual appliances or cascaded to form a common vent system.
SKU: n/a -
Chimney System, Heating
Centrotherm InnoFlue® Concentric
• InnoFlue® Concentric integrates our industry leading InnoFlue® Single Wall, flame retardant, polypropylene technology and white powder coated metal outers.
• This integrated system allows both flue gases and fresh air to flow through a single component, reducing installation time and roof or wall penetrations.
• InnoFlue® Concentric is UL-1738 and ULC-S636 listed. Suitable for Category II and IV or Canadian Type Gas Vent BH, Class II heating equipment.
• InnoFlue® Concentric is listed at zero clearance to combustibles.
• No glue or solvents required. Concentric Vent Lengths and fittings are joined using high performance EPDM gaskets which are suitable for service pressures up to 20’’WC and are resistant to corrosive condensate.
• Used to vent individual appliances. InnoFlue® Concentric can be combined with InnoFlue® SW and InnoFlue®
• Available in diameters of 2/4″, 3/5″, 4/6″ in vent Lengths of 1′, 2′ & 3′ (Effective Lengths)SKU: n/a -
Chimney System, Heating
Enervex CASI
Demand controlled exhaust system designed for commercial boilers and water heaters in buildings where the exhaust is powered by an inline power venter installed inside a building
Extremely low noise level
Priority Operation Function and Bearing Cycle Activation
Interlocks 6 appliances (standard) or as many as necessary with add-on boards
SS316L and aluminum impeller for use with Category I, II, III and IV appliances (condensing and noncondensing)
Spark-resistant construction with TEFC-motor with direct drive and true variable speed (inverter duty)
Maintenance free and service-friendly designSKU: n/a -
Chimney System, Heating
Enervex CASV
Demand controlled exhaust system designed for commercial boilers and water heaters in buildings where the exhaust is powered by a chimney fan on the exterior of the building
Extremely low noise level
Priority Operation Function and Bearing Cycle
Activation Interlocks 6 appliances (standard) or as many as necessary with add-on relay boards
Cast aluminum chimney fan and impeller for use with Category I, II, III and IV appliances (condensing and non-condensing)
Spark-resistant construction with high-temperature TEFC-motor with a Class H temperature rating, direct drive and true variable speed (inverter-duty)
Maintenance free and service-friendly designSKU: n/a -
Chimney System, Heating
Enervex MCAS
Demand controlled combustion or make-up air supply system
Extremely low noise level
Priority Operation Function and Bearing Cycle Activation
Interlocks 6 appliances (standard) or as many as necessary with add-on boards
Easy programming of essential functions (80 parameters are programmable for customized solutions)
Spark-resistant construction with TEFC-motor with direct drive and true variable speed (inverter duty)
Maintenance free and service-friendly designSKU: n/a -
Chimney System, Heating
Enervex MODS
Demand controlled exhaust system that’s designed for buildings that experience excessive chimney draft
Full modulation and 100% over-draft control
Integrated safety system with Proven Draft function, over-pressure cut-out switch and operation verification
Priority Operation Function and Bearing Cycle Activation
Interlocks 6 appliances (standard) or as many as necessary with add-on boards
Multi-blade damper for fast and accurate draft control
Fast-acting, direct drive actuator with brushless motor
Maintenance free and service-friendly design, the MODS System can be combined with a CASV or CASI and an MCAS systemSKU: n/a -
Chimney System, Heating
Enervex PowerStack Chimney Duct System
Industry-only multi-use chimney system with 9 UL listings
Only chimney system listed for use with Category I, II, III and IV appliances
Material Inner Liner: 316L-PCM Stainless Steel
Outer Case: 304 Stainless Steel Insulation Insulfrax 8.14 lbs/cu.ft (128 kg/m3)
Max. Pressure : 60 inWG (14945 Pa)
Max. Temperature1400°F (760°C) per UL2561
Warranty1-Year Warranty / Extended 15-Year Warranty
5-Year Performance and Leakage Guarantee
SKU: n/a -
Chimney System, Heating
Enervex UVS Ultimate Venting System
PowerStack Chimney System
Flexible, one-stop design eliminates guesswork
Mechanical Draft System (fan-based)
Modulating Overdraft Control System (damper-based)
Modulating Combustion Air Supply System Economizer (Vortex Heat Recovery System)
Guaranteed fit for all parts & components
Fit for any type of building, application or applianceSKU: n/a -
Chimney System, Heating
InnoFlue® Flex polypropylene venting systems
Lightweight flexible polypropylene venting eliminates installation fatigue associated with most common venting materials. Continuous vent length up to 150′ allows for the rapid lining of chimneys, b-vents, and other chases.
Industry leading flame retardant polypropylene technology rated to 230°F, tested to UL-1738 and ULC-S636. InnoFlue® is zero clearance to combustibles. Suitable for Category II and IV or Canadian Type Gas Vent BH, Class II heating equipment.
Available in 2’’, 3’’ and 4’’ diameter kits
Can be combined with InnoFlue® SW and/or InnoFlue® Concentric productsSKU: n/a
-
Chimney System, Heating
Centrotherm BlitzFlex®
- Flexible air-intake system.
- Made from flexible polymer BlitzFlex® comes in an easy to dispense BlitzPack box.
- A single box provides enough flexible air-intake conduit to complete 3 to 5 standard residential systems.
- Available in 2’’, 3’’ and 4’’ diameter they can be combined with BlitzKits which includes a rigid vent length, a 45° elbow, an appliance adaptor, and support clamps.
- Residential and light commercial air-intake installations have never been faster and easier.
-
Chimney System, Heating
Centrotherm InnoFlue®
- Single wall polypropylene venting systems
- InnoFlue® polypropylene venting system come in a variety of sizes up to 10’ in length.
- Residential: 2’’, 3’’, 4’’ and 5’’ diameter – Commercial: 6’’, 8’’, 10’’ and 12’’ diameter.
- Industry leading flame retardant polypropylene technology rated to 230°F, tested to UL-1738 and ULC-S636.
- Zero clearance to combustibles and is suitable for Category II and IV or Type BH Gas Vent.
- No glue or solvent required.
- Vent Lengths and fittings are joined using high performance EPDM gaskets which are suitable for service pressures up to 20’’WC.
- Lightweight polypropylene eliminates installation fatigue associated with overhead installation of most common venting materials.
- Can be configured to vent individual appliances or cascaded to form a common vent system.
-
Chimney System, Heating
Centrotherm InnoFlue® Concentric
• InnoFlue® Concentric integrates our industry leading InnoFlue® Single Wall, flame retardant, polypropylene technology and white powder coated metal outers.
• This integrated system allows both flue gases and fresh air to flow through a single component, reducing installation time and roof or wall penetrations.
• InnoFlue® Concentric is UL-1738 and ULC-S636 listed. Suitable for Category II and IV or Canadian Type Gas Vent BH, Class II heating equipment.
• InnoFlue® Concentric is listed at zero clearance to combustibles.
• No glue or solvents required. Concentric Vent Lengths and fittings are joined using high performance EPDM gaskets which are suitable for service pressures up to 20’’WC and are resistant to corrosive condensate.
• Used to vent individual appliances. InnoFlue® Concentric can be combined with InnoFlue® SW and InnoFlue®
• Available in diameters of 2/4″, 3/5″, 4/6″ in vent Lengths of 1′, 2′ & 3′ (Effective Lengths) -
Chimney System, Heating
Enervex CASI
Demand controlled exhaust system designed for commercial boilers and water heaters in buildings where the exhaust is powered by an inline power venter installed inside a building
Extremely low noise level
Priority Operation Function and Bearing Cycle Activation
Interlocks 6 appliances (standard) or as many as necessary with add-on boards
SS316L and aluminum impeller for use with Category I, II, III and IV appliances (condensing and noncondensing)
Spark-resistant construction with TEFC-motor with direct drive and true variable speed (inverter duty)
Maintenance free and service-friendly design -
Chimney System, Heating
Enervex CASV
Demand controlled exhaust system designed for commercial boilers and water heaters in buildings where the exhaust is powered by a chimney fan on the exterior of the building
Extremely low noise level
Priority Operation Function and Bearing Cycle
Activation Interlocks 6 appliances (standard) or as many as necessary with add-on relay boards
Cast aluminum chimney fan and impeller for use with Category I, II, III and IV appliances (condensing and non-condensing)
Spark-resistant construction with high-temperature TEFC-motor with a Class H temperature rating, direct drive and true variable speed (inverter-duty)
Maintenance free and service-friendly design -
Chimney System, Heating
Enervex MCAS
Demand controlled combustion or make-up air supply system
Extremely low noise level
Priority Operation Function and Bearing Cycle Activation
Interlocks 6 appliances (standard) or as many as necessary with add-on boards
Easy programming of essential functions (80 parameters are programmable for customized solutions)
Spark-resistant construction with TEFC-motor with direct drive and true variable speed (inverter duty)
Maintenance free and service-friendly design -
Chimney System, Heating
Enervex MODS
Demand controlled exhaust system that’s designed for buildings that experience excessive chimney draft
Full modulation and 100% over-draft control
Integrated safety system with Proven Draft function, over-pressure cut-out switch and operation verification
Priority Operation Function and Bearing Cycle Activation
Interlocks 6 appliances (standard) or as many as necessary with add-on boards
Multi-blade damper for fast and accurate draft control
Fast-acting, direct drive actuator with brushless motor
Maintenance free and service-friendly design, the MODS System can be combined with a CASV or CASI and an MCAS system -
Chimney System, Heating
Enervex PowerStack Chimney Duct System
Industry-only multi-use chimney system with 9 UL listings
Only chimney system listed for use with Category I, II, III and IV appliances
Material Inner Liner: 316L-PCM Stainless Steel
Outer Case: 304 Stainless Steel Insulation Insulfrax 8.14 lbs/cu.ft (128 kg/m3)
Max. Pressure : 60 inWG (14945 Pa)
Max. Temperature1400°F (760°C) per UL2561
Warranty1-Year Warranty / Extended 15-Year Warranty
5-Year Performance and Leakage Guarantee
-
Chimney System, Heating
Enervex UVS Ultimate Venting System
PowerStack Chimney System
Flexible, one-stop design eliminates guesswork
Mechanical Draft System (fan-based)
Modulating Overdraft Control System (damper-based)
Modulating Combustion Air Supply System Economizer (Vortex Heat Recovery System)
Guaranteed fit for all parts & components
Fit for any type of building, application or appliance -
Chimney System, Heating
InnoFlue® Flex polypropylene venting systems
Lightweight flexible polypropylene venting eliminates installation fatigue associated with most common venting materials. Continuous vent length up to 150′ allows for the rapid lining of chimneys, b-vents, and other chases.
Industry leading flame retardant polypropylene technology rated to 230°F, tested to UL-1738 and ULC-S636. InnoFlue® is zero clearance to combustibles. Suitable for Category II and IV or Canadian Type Gas Vent BH, Class II heating equipment.
Available in 2’’, 3’’ and 4’’ diameter kits
Can be combined with InnoFlue® SW and/or InnoFlue® Concentric products
-
Chimney System, Heating
Centrotherm BlitzFlex®
- Flexible air-intake system.
- Made from flexible polymer BlitzFlex® comes in an easy to dispense BlitzPack box.
- A single box provides enough flexible air-intake conduit to complete 3 to 5 standard residential systems.
- Available in 2’’, 3’’ and 4’’ diameter they can be combined with BlitzKits which includes a rigid vent length, a 45° elbow, an appliance adaptor, and support clamps.
- Residential and light commercial air-intake installations have never been faster and easier.
-
Chimney System, Heating
Centrotherm InnoFlue®
- Single wall polypropylene venting systems
- InnoFlue® polypropylene venting system come in a variety of sizes up to 10’ in length.
- Residential: 2’’, 3’’, 4’’ and 5’’ diameter – Commercial: 6’’, 8’’, 10’’ and 12’’ diameter.
- Industry leading flame retardant polypropylene technology rated to 230°F, tested to UL-1738 and ULC-S636.
- Zero clearance to combustibles and is suitable for Category II and IV or Type BH Gas Vent.
- No glue or solvent required.
- Vent Lengths and fittings are joined using high performance EPDM gaskets which are suitable for service pressures up to 20’’WC.
- Lightweight polypropylene eliminates installation fatigue associated with overhead installation of most common venting materials.
- Can be configured to vent individual appliances or cascaded to form a common vent system.
-
Chimney System, Heating
Centrotherm InnoFlue® Concentric
• InnoFlue® Concentric integrates our industry leading InnoFlue® Single Wall, flame retardant, polypropylene technology and white powder coated metal outers.
• This integrated system allows both flue gases and fresh air to flow through a single component, reducing installation time and roof or wall penetrations.
• InnoFlue® Concentric is UL-1738 and ULC-S636 listed. Suitable for Category II and IV or Canadian Type Gas Vent BH, Class II heating equipment.
• InnoFlue® Concentric is listed at zero clearance to combustibles.
• No glue or solvents required. Concentric Vent Lengths and fittings are joined using high performance EPDM gaskets which are suitable for service pressures up to 20’’WC and are resistant to corrosive condensate.
• Used to vent individual appliances. InnoFlue® Concentric can be combined with InnoFlue® SW and InnoFlue®
• Available in diameters of 2/4″, 3/5″, 4/6″ in vent Lengths of 1′, 2′ & 3′ (Effective Lengths) -
Chimney System, Heating
Enervex CASI
Demand controlled exhaust system designed for commercial boilers and water heaters in buildings where the exhaust is powered by an inline power venter installed inside a building
Extremely low noise level
Priority Operation Function and Bearing Cycle Activation
Interlocks 6 appliances (standard) or as many as necessary with add-on boards
SS316L and aluminum impeller for use with Category I, II, III and IV appliances (condensing and noncondensing)
Spark-resistant construction with TEFC-motor with direct drive and true variable speed (inverter duty)
Maintenance free and service-friendly design -
Chimney System, Heating
Enervex CASV
Demand controlled exhaust system designed for commercial boilers and water heaters in buildings where the exhaust is powered by a chimney fan on the exterior of the building
Extremely low noise level
Priority Operation Function and Bearing Cycle
Activation Interlocks 6 appliances (standard) or as many as necessary with add-on relay boards
Cast aluminum chimney fan and impeller for use with Category I, II, III and IV appliances (condensing and non-condensing)
Spark-resistant construction with high-temperature TEFC-motor with a Class H temperature rating, direct drive and true variable speed (inverter-duty)
Maintenance free and service-friendly design -
Chimney System, Heating
Enervex MCAS
Demand controlled combustion or make-up air supply system
Extremely low noise level
Priority Operation Function and Bearing Cycle Activation
Interlocks 6 appliances (standard) or as many as necessary with add-on boards
Easy programming of essential functions (80 parameters are programmable for customized solutions)
Spark-resistant construction with TEFC-motor with direct drive and true variable speed (inverter duty)
Maintenance free and service-friendly design -
Chimney System, Heating
Enervex MODS
Demand controlled exhaust system that’s designed for buildings that experience excessive chimney draft
Full modulation and 100% over-draft control
Integrated safety system with Proven Draft function, over-pressure cut-out switch and operation verification
Priority Operation Function and Bearing Cycle Activation
Interlocks 6 appliances (standard) or as many as necessary with add-on boards
Multi-blade damper for fast and accurate draft control
Fast-acting, direct drive actuator with brushless motor
Maintenance free and service-friendly design, the MODS System can be combined with a CASV or CASI and an MCAS system -
Chimney System, Heating
Enervex PowerStack Chimney Duct System
Industry-only multi-use chimney system with 9 UL listings
Only chimney system listed for use with Category I, II, III and IV appliances
Material Inner Liner: 316L-PCM Stainless Steel
Outer Case: 304 Stainless Steel Insulation Insulfrax 8.14 lbs/cu.ft (128 kg/m3)
Max. Pressure : 60 inWG (14945 Pa)
Max. Temperature1400°F (760°C) per UL2561
Warranty1-Year Warranty / Extended 15-Year Warranty
5-Year Performance and Leakage Guarantee
-
Chimney System, Heating
Enervex UVS Ultimate Venting System
PowerStack Chimney System
Flexible, one-stop design eliminates guesswork
Mechanical Draft System (fan-based)
Modulating Overdraft Control System (damper-based)
Modulating Combustion Air Supply System Economizer (Vortex Heat Recovery System)
Guaranteed fit for all parts & components
Fit for any type of building, application or appliance -
Chimney System, Heating
InnoFlue® Flex polypropylene venting systems
Lightweight flexible polypropylene venting eliminates installation fatigue associated with most common venting materials. Continuous vent length up to 150′ allows for the rapid lining of chimneys, b-vents, and other chases.
Industry leading flame retardant polypropylene technology rated to 230°F, tested to UL-1738 and ULC-S636. InnoFlue® is zero clearance to combustibles. Suitable for Category II and IV or Canadian Type Gas Vent BH, Class II heating equipment.
Available in 2’’, 3’’ and 4’’ diameter kits
Can be combined with InnoFlue® SW and/or InnoFlue® Concentric products